manualshive.com logo in svg

Analog Devices adsp-2100, Manual

The Analog Devices ADSP-2100 user manual is available for free download on our website. This comprehensive manual provides detailed instructions and valuable insights on utilizing the ADSP-2100 effectively. Unlock the full potential of this exceptional product by accessing the manual from manualshive.com.

Share
Download
background image

System Interface

9

9 – 4

Using a 1X or 1/2X frequency input clock with the phase-locked loop to
generate the various internal clocks imposes certain restrictions. The CLKIN
signal must be valid long enough to achieve phase lock before 

RESET

 can be

deasserted. Also, the clock frequency cannot be changed unless the processor
is in 

RESET

. Refer to the processor data sheets for details.

9.3

RESET

RESET

 halts execution and causes a hardware reset of the processor. The

RESET

 signal must be asserted when the processor is powered up to assure

proper initialization.

Tables 9.2–9.7 show the 

RESET

 state of various registers, including the

processors’ on-chip memory-mapped status/control registers. The values of
any registers not listed are undefined at reset. The contents of on-chip
memory are unchanged after 

RESET

, except as shown in Tables 9.2–9.7 for

the data-memory-mapped control/status registers. The CLKOUT signal
continues to be generated by the processor during 

RESET

, except when

disabled on the ADSP-2171, ADSP-2181, or ADSP-21msp58/59.

The contents of the computation unit (ALU, MAC, Shifter) and data address
generator (DAG1, DAG2) registers are undefined following 

RESET

.

When 

RESET

 is released, the processor’s booting operation takes place,

depending on the state of the processor’s MMAP pin. Program booting is
described in Chapter 10, “Memory Interface.”

For the ADSP-2111, ADSP-2171, and ADSP-21msp58/59 processors, which
include a host interface port, setting the software reset bit in the HSR7
register has the same affect as asserting 

RESET

. This allows either the host

processor or the ADSP-21xx to initiate a reset under software control.

In a multiprocessing system with several processors, a synchronous 

RESET

 is

required.

9.4

SOFTWARE-

FORCED REBOOTING

Software-forced reboots can be accomplished in several ways. A software-
forced reboot clears the context of the processor and initializes some
registers. A context clear clears the processor stacks and restart execution at
address 0x0000. Table 9.1 shows the different ways each processor can
perform a software reboot.

Summary of Contents for adsp-2100







































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for adsp-2100

Paradyne 3172 Quick Reference preview
3172
Brand: Paradyne Pages: 20
Paradyne Compshere 3000 Series Notice preview
Compshere 3000 Series
Brand: Paradyne Pages: 2
Paradyne MCC Installation Instructions Manual preview
MCC
Brand: Paradyne Pages: 11
Paradyne Hotwire 8784 Installation Instructions Manual preview
Hotwire 8784
Brand: Paradyne Pages: 19
Paradyne COMSPHERE 3550 Series User Manual preview
COMSPHERE 3550 Series
Brand: Paradyne Pages: 153
Paradyne Jetstream CPX-1000 Reference Manual preview
Jetstream CPX-1000
Brand: Paradyne Pages: 141
National Instruments Fieldpoint cFP-RTD-124 Operating Instructions Manual preview
Fieldpoint cFP-RTD-124
Brand: National Instruments Pages: 15
Lancom 7100 VPN Manual preview
7100 VPN
Brand: Lancom Pages: 70
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
Tait TM9000 Installation Instructions Manual preview
TM9000
Brand: Tait Pages: 8
C4i GEN-1 Quick Operation Manual preview
GEN-1
Brand: C4i Pages: 5
MICROENER IM30-CV Operation Manual preview
IM30-CV
Brand: MICROENER Pages: 24
Crest Audio NC-MCO - TECHNICAL Technical Data preview
NC-MCO - TECHNICAL
Brand: Crest Audio Pages: 2
ekwb EK-Quantum Vector TUF RX 6800 User Manual preview
EK-Quantum Vector TUF RX 6800
Brand: ekwb Pages: 14
ST STM32MP157 Series User Manual preview
STM32MP157 Series
Brand: ST Pages: 47
Westermo Viper-012 User Manual preview
Viper-012
Brand: Westermo Pages: 22
LanReady AP-952X User Manual preview
AP-952X
Brand: LanReady Pages: 40
V7 SCREENSHARE PRO User Manual preview
SCREENSHARE PRO
Brand: V7 Pages: 4

Brands by name

Popular brands

Load more brands