manualshive.com logo in svg

Analog Devices adsp-2100, Manual

The Analog Devices ADSP-2100 user manual is available for free download on our website. This comprehensive manual provides detailed instructions and valuable insights on utilizing the ADSP-2100 effectively. Unlock the full potential of this exceptional product by accessing the manual from manualshive.com.

Share
Download
background image

7

Host Interface Port

7 –
9

two consecutive reads—the second read will generate the correct status information (the
first read generates the previous status).

In Figure 7.3, host status synchronization is based on a pseudo-clock HCLK,
internal to the ADSP-21xx, which is a logical combination of 

HRD

, 

HWR

 and 

HSEL

.

The first event shown in the figure is a status change at d1. The host status will
then be updated after the HCLK low, HCLK high, HCLK low sequence at point
c1. A status change at d2 would wait for the HCLK low, HCLK high, HCLK low
sequence, and then host status would be updated at point c2.

Status synchronization for the ADSP-21xx requires one full CLKOUT cycle
(starting at the rising edge) after a status change. As shown in Figure 7.4, a status
change at point d1 would cause a 21xx HIP status update at c1. A status change
at d2 would cause a 21xx HIP status update at c2.

7.4.2

Interrupt-Driven Operation

Using an interrupt-driven protocol frees the host and the ADSP-21xx from
polling   the HSR(s) to see when data is ready to be read. For interrupt-driven
transfers to the ADSP-21xx, the host writes data into an HDR, and the HIP
automatically generates  an internal interrupt. The interrupt is serviced like any
other interrupt.

For transfers to the host, the ADSP-21xx writes data to an HDR, then sets a flag
output, which is connected to a host interrupt input, to signal the host that new
data  is ready to be transferred. Flag outputs are discussed in detail in Chapter 9,
“System Interface.” If the ADSP-21xx passes data to the host through only one
HDR, then that HDR can be read directly by the host when it receives the
interrupt.  If more than one HDR is used to pass data, then the host must read
the appropriate HSR(s) to determine which HDR was written by the ADSP-21xx.

7.4.3

HDR Overwrite Mode

In most cases, the ADSP-21xx reads host data sent through the HIP faster than
the host can send them. However, if the host is sufficiently fast, if the ADSP-21xx
is busy, or if the ADSP-21xx is driven by a slow clock, there may  be a delay in
servicing a  host write interrupt. If the host computer uses a handshaking
protocol requiring the ADSP-21xx to assert 

HACK

 to complete a host transfer, the

ADSP-21xx can optionally hold off the next host write until it has processed the
current one.

If the HDR overwrite bit (bit 7 in HSR7) is cleared, and if the host tries to write to
a register before it has been read by the ADSP-21xx, 

HACK

 is not asserted until

the ADSP-21xx has read the previously written data. The host processor must
wait for 

HACK

 to be asserted. As described earlier, however, there is a delay from

when the host writes data to when the status is synchronized to the ADSP-21xx.
During this interval, it is possible for the host to write an HDR a second time
even when the overwrite bit is cleared.

Summary of Contents for adsp-2100







































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for adsp-2100

Magma PE6R4-I Quick Installation Manual preview
PE6R4-I
Brand: Magma Pages: 2
peplink balance ONE Manual preview
balance ONE
Brand: peplink Pages: 2
Navitar 1-62645 Dimensional Drawing preview
1-62645
Brand: Navitar Pages: 1
Cypress Semiconductor CY7C1303BV25 Specification Sheet preview
CY7C1303BV25
Brand: Cypress Semiconductor Pages: 19
Xtreme SNMP-1PMINI User & Installation Manual preview
SNMP-1PMINI
Brand: Xtreme Pages: 83
Vacron VDH-NK300 Hardware Manual preview
VDH-NK300
Brand: Vacron Pages: 16
Stahl HFisolator 9730/26-11 Operating Instructions preview
HFisolator 9730/26-11
Brand: Stahl Pages: 2
Amphenol C2LINX Series Installation Manual preview
C2LINX Series
Brand: Amphenol Pages: 43
Renesas RL78/L1C User Manual preview
RL78/L1C
Brand: Renesas Pages: 4
Forcepoint V10000 G4R2 Quick Start Manual preview
V10000 G4R2
Brand: Forcepoint Pages: 2
Allied Telesis AR440S Hardware Reference Manual preview
AR440S
Brand: Allied Telesis Pages: 44
Cognex 800-5815-1 Installation And Reference Manual preview
800-5815-1
Brand: Cognex Pages: 57
KTI Networks KGS-2421 User Manual preview
KGS-2421
Brand: KTI Networks Pages: 147
StarTech.com DRW150SATBK Instruction Manual preview
DRW150SATBK
Brand: StarTech.com Pages: 10
3onedata MODEL277 Series Quick Installation Manual preview
MODEL277 Series
Brand: 3onedata Pages: 3
Sandberg Nano User Manual preview
Nano
Brand: Sandberg Pages: 9
Ingrasys nastorage 12600 series User Manual preview
nastorage 12600 series
Brand: Ingrasys Pages: 158
IPEX PH232T485Y14 User Manual preview
PH232T485Y14
Brand: IPEX Pages: 17

Brands by name

Popular brands

Load more brands