manualshive.com logo in svg

Analog Devices adsp-2100, Manual

The Analog Devices ADSP-2100 user manual is available for free download on our website. This comprehensive manual provides detailed instructions and valuable insights on utilizing the ADSP-2100 effectively. Unlock the full potential of this exceptional product by accessing the manual from manualshive.com.

Share
Download
background image

8 Analog Interface

8 – 6

8.3

D/A CONVERSION

The D/A conversion circuitry of the ADSP-21msp58/59’s analog
interface consists of a sigma-delta digital-to-analog converter (DAC),
an analog smoothing filter, a programmable gain amplifier, and a
differential output amplifier.

8.3.1

DAC

The analog interface’s DAC implements digital filters and a sigma-
delta modulator with the same characteristics as the filters and
modulator of the ADC. The DAC consists of a digital high pass filter,
an anti-imaging interpolation filter, and a digital sigma-delta
modulator.

The DAC receives 16-bit data values from the ADSP-21msp58/59’s
DAC Transmit data register (which is memory-mapped at address
0x3FEC in data memory). The data stream is filtered first by the DAC’s
high pass filter and then by the anti-imaging interpolation filter. These
filters have the same characteristics as the ADC’s anti-aliasing
decimation filter and digital high pass filter.

The output of the interpolation filter is fed to the DAC’s digital sigma-
delta modulator, which converts the 16-bit data to 1-bit samples at a
1.0 MHz rate. The modulator noise-shapes the signal such that errors
inherent to the process are minimized in the passband of the converter.

The bit stream output of the sigma-delta modulator is fed to the DAC’s
analog smoothing filter where it is converted to an analog voltage.

8.3.1.1 High Pass Filter

The DAC’s digital high pass filter has the same characteristics as the
high pass filter of the ADC. The high pass filter removes frequency
components at the low end of the spectrum; it attenuates signal energy
below the passband of the converter. The DAC’s high pass filter can be
bypassed by setting bit 8 (DABY) of the ADSP-21msp58/59’s analog
control register.

Summary of Contents for adsp-2100







































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for adsp-2100

Cabletron Systems Netlink FRX4000 Installation And Setup Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 8
Cabletron Systems 9C300-1 Upgrade Instructions preview
9C300-1
Brand: Cabletron Systems Pages: 4
CAME QBEMFSB2 User Manual preview
QBEMFSB2
Brand: CAME Pages: 19
Lanner NCA-2510 Installation Manual preview
NCA-2510
Brand: Lanner Pages: 2
Tripp Lite N48M Series Installation Manual preview
N48M Series
Brand: Tripp Lite Pages: 20
Acqiris SA217P Startup Manual preview
SA217P
Brand: Acqiris Pages: 22
Renesas Asynchronous SH7145F Application Note preview
Asynchronous SH7145F
Brand: Renesas Pages: 17
Jetter JetWeb JX2-PR0FI1 Operator'S Manual preview
JetWeb JX2-PR0FI1
Brand: Jetter Pages: 67
S&T kontron KBox E-420-R1K/V1K User Manual preview
kontron KBox E-420-R1K/V1K
Brand: S&T Pages: 82
Freescale Semiconductor MPC8349EA MDS Getting Started Manual preview
MPC8349EA MDS
Brand: Freescale Semiconductor Pages: 8
Swann NVRx-7300 series Quick Start Manual preview
NVRx-7300 series
Brand: Swann Pages: 9
Kaya Instruments KY-FGK Reference Manual preview
KY-FGK
Brand: Kaya Instruments Pages: 48
V-Count Ultima Go Quick Installation Manual preview
Ultima Go
Brand: V-Count Pages: 2
Digi DataFire GO! PRO Manual preview
DataFire GO! PRO
Brand: Digi Pages: 20
Kontron AdvancedTCA AT8901M User Manual preview
AdvancedTCA AT8901M
Brand: Kontron Pages: 76
Uctronics U6180 Instruction Manual preview
U6180
Brand: Uctronics Pages: 2
S&P Turbo-3000 Operating Instructions preview
Turbo-3000
Brand: S&P Pages: 3
ProSoft MVI46-PDPS User Manual preview
MVI46-PDPS
Brand: ProSoft Pages: 53

Brands by name

Popular brands

Load more brands