Analog Devices adsp-2100 Manual Download | Manualshive

Page: 163 / 486

background image

7

Host Interface Port

7 –
17

2. The host waits at least two ADSP-21xx processor cycles.

3. Starting with the instruction which is to be loaded into the highest

address of internal program memory, the host writes an instruction
into HDR0, HDR2 and HDR1 (in that order), one byte each. The upper
byte goes into HDR0, the lower byte goes into HDR2 and the middle
byte goes into HDR1.

4. The address of the instruction is decremented, and Step 3 is repeated.

This continues until the last instruction has been loaded into the HIP.

The ADSP-21xx reads the length of the boot load first, then bytes are
loaded from the highest address downwards. This results in shorter
booting times for shorter loads.

The number of instructions booted must be a multiple of eight. The boot
length value is given as:

length = (number of 24-bit program memory words ÷ 8) – 1

That is, a length of 0 causes the HIP to load eight 24-bit words.

In most cases, no handshaking is necessary, and the host can transfer data
at the maximum rate it is capable of. If the host operates faster than the
ADSP-21xx, wait states or NOPs must be added to the host cycle to slow it
down to one write every ADSP-21xx clock cycle.

«
...
161
162
163
164
165
...
»

Summary of Contents for adsp-2100







































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for adsp-2100

Brand: Mackie Pages: 2

Brand: Mackie Pages: 5

Brand: TFortis Pages: 86

Brand: Intel Pages: 108

Brand: Waves Pages: 41

HHM Series HHM2411

Brand: TDK Pages: 2

Brand: Wyse Pages: 8

Brand: JAKA Pages: 37

H8S/2646 Series

Brand: Renesas Pages: 20

Brand: M-system Pages: 4

Brand: ZALMAN Pages: 20

Brand: Cypress Semiconductor Pages: 9

Brand: ADLINK Technology Pages: 86

PCI-AD-x16HE-BG4

Brand: Serial Cables Pages: 18

Brand: The t.racks Pages: 24

Brand: COMBA Pages: 57

Brand: Exsys Pages: 2

Brand: IBASE Technology Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands