![background image](http://html1.mh-extra.com/html/amx/modero-cv7/modero-cv7_operation-reference-manual_2939251071.webp)
Configuring Communication
59
7" Modero Touch Panels
Wireless communication using a Static IP Address
1.
Press the
Protected Setup
button (located on the lower-left of the panel page) to open the Protected
Setup page and display an on-screen keypad.
2.
Enter
1988
into the Keypad’s password field and press
Done
when finished.
3.
Press the
Wireless Settings
button (located on the lower-left) to open the Wireless Settings page.
Wireless communication is set within the IP Settings section of this page (FIG. 58).
4.
Toggle the
DHCP/Static
field (
from the IP Settings section
) until the choice cycles to
Static
.
The IP Address, Subnet Mask, and Gateway fields then become user-editable (red).
5.
Press the
IP Address
field to open a Keyboard and enter the Static IP Address (
provided by your
System Administrator
).
6.
Press
Done
after you are finished entering the IP information.
7.
Repeat the same process for the
Subnet Mask
and
Gateway
fields.
8.
Press the optional
Host Name
field to open the Keyboard and enter the Host Name information.
9.
Press
Done
after you are finished assigning the alpha-numeric string of the host name.
10.
Press the Primary DNS field to open a Keyboard, enter the Primary DNS Address (provided by your
System Administrator) and press
Done
when compete. Repeat this process for the Secondary DNS
field.
11.
Press the Domain field to open a Keyboard, enter the resolvable domain Address (this is provided
by your System Administrator and equates to a unique Internet name for the panel), and press
Done
when complete.
12.
Setup the security and communication parameters between the wireless card and the target WAP by
configuring the Wireless Settings section on this page. Refer to the following section for detailed
procedures to setup either a secure or unsecure connection.
Using the Site Survey tool
This tool allows a user to "sniff-out" all transmitting Wireless Access Points within the detection range
of the internal NXA-WC80211GCF
(
this feature is not available with the 802.11b Wi-Fi card
)
. Once
pressed, the panel displays the Site Survey page which contains categories such as:
Network Name
(SSID) - Wireless Access Point names
Channel
(RF) - Channel currently being used by the WAP (
Wireless Access Point
)
Security Type
(if detectable - such as
WEP
,
OPEN
and
UNKNOWN
) - security protocol
enabled on the WAP
Signal Strength
- None, Poor, Fair, Good, Very Good, and Excellent
MAC Address
- Unique identification of the transmitting Access Point
1.
Press the
Wireless Settings
button (located on the lower-left) to open the Wireless Settings page.
2.
Navigate to the Access Point MAC Address section of this page and press the on-screen
Site Survey
button. This action launches the Site Survey page which displays a listing of all
detected WAPs in the communication range of the internal card.
The card scans its environment every four seconds and adds any new WAPs found to the list.
Every scan cycle updates the signal strength field.
Check with your System Administrator for a pre-reserved Static IP Address assigned
to the panel. This address must be obtained before Static assignment of the panel
continues.
Summary of Contents for Modero CV7
