![background image](http://html1.mh-extra.com/html/amx/modero-cv7/modero-cv7_operation-reference-manual_2939251016.webp)
Introduction
4
7" Modero Touch Panels
Specifications for 7" Widescreen Video Touch Panels (Cont.)
IR Receiver:
• IR reception: 38 KHz IR frequency.
• The IR receiver is located beneath the translucent Front Setup button. When
an IR code is detected it is sent to the NetLinx Master as a push on the
appropriate AMX IR channel.
• IR receivers and transmitters on G4 panels share the device address number
of the panel.
Front setup access button:
• Provides both access to the Setup and Calibration page and toggles the
panel between a "sleep" or "wake" state.
- When wired, "sleep" status means the backlight is Off.
- When battery operated, wireless "sleep" status means the touch panel
base is either Off or "suspended".
Microphone:
• Used for intercom applications
(
requires the NXA-AVB/ETHERNET Breakout Box for analog
communication
)
Speakers:
• Stereo output with a frequency response of 500 Hz - 7 KHz
LEDs (
NXD panels only
):
• 6 blue LEDs (support On and Off)
- Both the LEDs and pushbuttons are only available when using the default
Button Trim Ring on the NXD panel.
Buttons (
NXD panels only
):
• 6 programmable pushbuttons
Rear Panel Components:
(Side panel location on NXD-Wall Mount panels)
Mini-USB connector:
• 5-pin Mini-USB connector used for programming, firmware update, and touch
panel file transfer between the PC and the target panel.
Note
: When connecting the panel to PC using a CC-USB (or compatible)
cable, be sure to power the panel On before attempting to connect the USB
cable from the PC to the mini-USB port on the panel. Refer to the Configuring
and Using USB with a Virtual Master
section on page 51
for more
information.
Stereo Output connector:
• Stereo output through a 3.5mm mini-jack (for use with external speakers or
headphones).
Ethernet 10/100 port:
• RJ-45 port for 10/100 Mbps communication. The Ethernet port automatically
negotiates the connection speed (10 Mbps or 100 Mbps), and whether to use
half duplex or full duplex mode.
• CV7 panels communicate with the NetLinx Master using the ICSP protocol
over Ethernet.
Ethernet 10/100 LEDs:
• LEDs show communication activity and connection information:
A
-activity - Yellow LED lights when receiving or transmitting Ethernet data
packets.
L
-link - Green LED lights when the Ethernet cables are connected and
terminated correctly.
USB connector:
• Type-A USB port can connect an external keyboard or mouse device for use
with Virtual PC applications.
Note
: External USB input devices (keyboard or mouse) must be plugged into
the rear/side USB connector
before
the unit is powered-up. The panel will not
detect these USB input devices until the unit cycles power.
Audio/Video connector:
• RJ-45 connector for communication of differential audio/video signals
to/from the touch panel (panel type dependant). This connector receives
Composite video, Stereo (left/right) audio, and microphone audio.
• Video is received via the NXA-AVB/ETHERNET Breakout Box. Configuring
video windows for playback is done using TPDesign4.
• In-bound audio (from the breakout box) gets directed to the speakers.
• Out-bound audio is sent from the on-board microphone (on the
front-panel). Selecting audio files for playback is configured through
TPDesign4.
PWR connector:
• 2-pin 3.5 mm mini-Phoenix connector.
Summary of Contents for Modero CV7
