American Megatrends MegaRAC G3 User Manual Download Page 121

Page: 121 / 151

Appendix B : G3ConfigApp

113

Appendix B

G3ConfigApp

Overview

The MegaRAC G3 card is normally configured through the Internet browser-based

Remote Access Companion for MegaRAC G3.

You can also configure your MegaRAC

G3 card through the

G3ConfigApp

utility. The

G3ConfigApp

utility is a GUI-based

program that runs in Microsoft Windows.

G3ConfigApp

Step Description

1 The

G3ConfigApp

program allows you to configure the MegaRAC G3 card. You can run the

G3ConfigApp

program from the host system or from a client system. The client system is the system that

will connect to the MegaRAC G3 card remotely through the network. This is basically WinCuri with a
GUI.

To run the

G3ConfigApp

program, double left click the

G3ConfigApp.exe

icon located in either of

the following directories on your

MegaRAC G3 CD:

•

CDROM\RemoteTools\Win32\

•

CDROM\ServerAgent\Win32\

The following window appears:

If you are running the

G3ConfigApp

program from the host system, select the first radial button labeled

‘

I am on the server which has a G3 plugged in’

and left click on the

button.

Note:

Make sure that the

MegaRAC G3

card is connected to the host system’s motherboard through

the USB cable.

Cont’d

Summary of Contents for MegaRAC G3
























































































































































Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands

American Megatrends MegaRAC G3, User Manual

Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands