American Megatrends MegaRAC G3 User Manual Download Page 117

Page: 117 / 151

Chapter Four : Using Your MegaRAC G3

109

General Information,

Continued

General Information : Features

Parameter Description

Virtual Floppy

This field displays whether or not floppy redirection is available.

Virtual CDROM

This field displays whether or not CD-ROM redirection is available.

Virtual
Keyboard/Mouse

This field displays the type of emulation is used for the keyboard and
mouse. USB emulation is not available in this version of MegaRAC
G3.

KVM over IP Support

This field displays whether or not KVM over IP is supported.

General Information : Detailed Versions

Parameter Description

Parameter

This column gives the name of the parameter.

Value

This column gives the version of the parameter.

Summary of Contents for MegaRAC G3
























































































































































Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands

American Megatrends MegaRAC G3, User Manual

Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands