American Megatrends MegaRAC G3 User Manual Download Page 118

Page: 118 / 151

MegaRAC G3 User’s Guide

110

Last Saved Crash Screen

This menu item allows you to view the last text-based screen in the event that the host
system locks up or freezes during a blue screen. This is useful because it allows you to
troubleshoot the host system. You will be prompted to login.

Note:

The maximum size that the

Crash Screen

image can be is 50 Kb. Because of this, only

one

Crash Screen

image can be saved. Also, only text-based crashes can be captured.

Graphics-based freezes and lock ups are not captured to the

Crash Screen

program.

Note:

You cannot flush a captured

Crash Screen

image from the MegaRAC G3 card’s memory.

It will automatically be erased when another

Crash Screen

image is saved.

Summary of Contents for MegaRAC G3
























































































































































Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands

American Megatrends MegaRAC G3, User Manual

Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands