American Megatrends MegaRAC G3 User Manual Download Page 44

Page: 44 / 151

MegaRAC G3 User’s Guide

Locating Your MegaRAC G3 Card,

Continued

Step Description

If the IP range is correct,

RacTrendsSeek Locator

will locate the MegaRAC G3 card. It will list all

MegaRAC cards it has discovered.

Note:

If more than one MegaRAC G3 card is found, you can distinguish them by the MegaRAC G3

card’s name. The MegaRAC G3 card’s name consists of the words G3 and the IP address of
the MegaRAC G3 card’s NIC.

In this example, the MegaRAC G3 card’s IP address is 192.168.0.36. Double left click on the IP address
to start managing the MegaRAC G3 card and write down its IP address. Left click on the

Finish

button

after

RacTrendsSeek Locator

discovers all MegaRAC cards.

Congratulations! You have successfully located your MegaRAC G3 card.

Summary of Contents for MegaRAC G3
























































































































































Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands

American Megatrends MegaRAC G3, User Manual

Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands