American Megatrends MegaRAC G3 User Manual Download Page 6 | Manualshive

Page: 6 / 151

background image

MegaRAC G3 User’s Guide

vi

Limited Warranty

The buyer agrees that if this product proves to be defective, American Megatrends is only
obligated to repair or replace this product at American Megatrends’ discretion according
to the terms and conditions of the warranty registration card that accompanies this
product. American Megatrends shall not be liable in tort or contract for any loss or
damage, direct, incidental or consequential resulting from the use of this product. Please
see the

Warranty Registration Card

shipped with this product for full warranty details.

Technical Support

AMI provides technical support for AMI products purchased directly from AMI or from
an AMI-authorized reseller only.

If… Then…

You purchased this product from AMI or from
a certified AMI reseller,

Call AMI technical support at 770-246-8645.
Please be prepared to specify the serial
number of the product.

This AMI product was installed as part of a
system manufactured by a company other than
AMI or you purchased an AMI product from
an unauthorized reseller,

Call the technical support department of the
computer manufacturer or the unauthorized
reseller. AMI does not provide direct technical
support in this case.

If an American Megatrends MegaRAC™ G3 card fails to operate as described or you are
in doubt about a configuration option, please call technical support at 770-246-8645.

Web Site

We invite you to access the American Megatrends World Wide Web site at:

http://www.ami.com/

«
...
4
5
6
7
8
...
»

Summary of Contents for MegaRAC G3
























































































































































Reviews:

No comments

Related manuals for MegaRAC G3

Univerge SV8100

Brand: NEC Pages: 44

Brand: B2 Pages: 52

Brand: 3Com Pages: 18

Brand: Supermicro Pages: 24

Brand: Gate Pages: 8

Brand: Neo Instruments Pages: 2

DIRECTOR PRO series

Brand: MF DIGITAL Pages: 79

Brand: Infoblox Pages: 13

Brand: ZoneVu Pages: 15

Brand: FUNcube Pages: 23

Brand: ADTRAN Pages: 20

Brand: Ista Pages: 16

Brand: Xtreme Pages: 83

CORE 2 DUO E4000 - 3-2008

Brand: Intel Pages: 122

Brand: Digital Audio Corporation Pages: 164

Brand: XtendLan Pages: 17

Brand: NEC Pages: 26

Brand: DOD Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands