American Megatrends MegaRAC G3 User Manual Download Page 61

Page: 61 / 151

Chapter Four : Using Your MegaRAC G3

Redirection,

Continued

Console Redirection Window

Dropdown
Menu Item

Description

This dropdown menu contains the following dropdown menu items:

Start Console Redirection

This menu item can be used to begin

Console Redirection

Stop Console Redirection

This menu item can be used to halt

Console Redirection

Restart

This menu item can be used to stop

Console Redirection

and then

start

Console Redirection

again.

Full Screen

This menu item can be used to view the

Console Redirection

Full Screen

mode.

Note:

Set your client system’s screen resolution to 1024 x
768 so that you can view the host system in true full
screen.

Sync Cursor

This menu item can be used to synchronize or unsynchronize the
mouse cursor.

CDROM Redirection

This menu item can be used to start or stop the redirection of the
CD-ROM drive.

Console
Redirection

Floppy Redirection

This menu item can be used to start or stop the redirection of the
floppy drive.

Note:

Floppy Redirection

is not an available feature on all

versions of the MegaRAC G3 cards.

Cont’d

Summary of Contents for MegaRAC G3
























































































































































Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands

American Megatrends MegaRAC G3, User Manual

Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands