American Megatrends MegaRAC G3 User Manual Download Page 97

Page: 97 / 151

Chapter Four : Using Your MegaRAC G3

Network,

Continued

Item Description

Use the following IP
address

This option allows you to configure the MegaRAC G3’s IP
address with a static IP. The

IP Address

Subnet Mask

, and

Gateway

fields will become editable when this option is selected.

IP Address

This field allows you to set the MegaRAC G3’s IP address.

Subnet Mask

This field allows you to set the

Subnet Mask

The MegaRAC G3 resides on.

Gateway

This field allows you to set the MegaRAC G3’s

Gateway

access address.

Apply Button

This button allows you to save your configuration.

Note:

You are prompted to close your Internet browser and reconnect to the new IP address if
you make changes to the

Networking Information

screen.

Summary of Contents for MegaRAC G3
























































































































































Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands

American Megatrends MegaRAC G3, User Manual

Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands