American Megatrends MegaRAC G3 User Manual Download Page 129 | Manualshive

Page: 129 / 151

background image

Appendix C : MegaRAC G3 Remote Recovery Application (RRA)

121

Appendix C

MegaRAC G3 Remote
Recovery Application (RRA)

MegaRAC G3 Card Remote Recovery Application (RRA)

The

Remote Recovery Application (RRA)

is a recovery tool that can be executed from a

remote client system located on the same network as the MegaRAC G3 card. You can use
it to recover a failed flash attempt.

To run the

MegaRAC G3

Remote Recovery Application (RRA)

, double left click on the

RRA.exe

icon.

Note:

You must physically set the MegaRAC G3 card you want to recover into

Recovery Mode

.

To do this, simply short pins two and three on jumper JP12 on your MegaRAC G3 card.

Note:

Your MegaRAC G3 card must be write enabled before you can flash an image to it.
Confirm that pins one and two on jumper JP11 are shorted on your MegaRAC G3 card.

Note:

The firmware upgrade process is a crucial operation. Make sure that the chances of a
power or connectivity loss are minimal when performing this operation.

Button

Description

Card Settings

Left click the

Card Settings

button to configure the MegaRAC G3 card parameters.

Note:

You must configure the card parameters before you start flashing.

Start Flashing

Left click the

Start Flashing

button to begin flashing the firmware image to your

MegaRAC G3 card.

Done

Left click the

Done

button to end the

MegaRAC G3 Remote Recovery Application (RRA)

.

Note:

You must configure the card parameters before you can start flashing your MegaRAC G3
card’s firmware.

Cont’d

«
...
127
128
129
130
131
...
»

Summary of Contents for MegaRAC G3
























































































































































Reviews:

No comments

Related manuals for MegaRAC G3

Brand: ABB Pages: 66

Brand: Maco Pages: 38

Brand: TC Electronic Pages: 2

SCSI PC Card REX-9530V

Brand: Ratoc Systems Pages: 30

JetWeb JX2-PR0FI1

Brand: Jetter Pages: 67

Brand: NA Pages: 22

2000 IDU Series

Brand: EMS Pages: 52

LIQMAX III ELC-LMT120-ARGB

Brand: ENERMAX Pages: 32

Brand: EZCast Pages: 24

Tamar FCSAS102800

Brand: Bridgeworks Pages: 56

Brand: Corsair Pages: 10

Brand: NetBurner Pages: 30

MICROSPACE MSEBX800

Brand: DIGITAL-LOGIC Pages: 53

Brand: Robotis Pages: 10

X570 AORUS ELITE WIFI

Brand: Gigabyte Pages: 48

ibaPADU-S-IT-16

Brand: IBA Pages: 80

VDA-NVR2108W4KS2

Brand: Dahua Technology Pages: 363

IQ Switch IQS128

Brand: Azoteq Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands