American Megatrends MegaRAC G3 User Manual Download Page 23 | Manualshive

Page: 23 / 151

background image

Chapter Two : Installing Your MegaRAC G3 Card

15

Step 6 Install the American Megatrends MegaRAC G3 Windows Software
Components

American Megatrends

MegaRAC G3

Windows Software Components

is a collection of

MegaRAC G3 host-side and remote access components. These programs are briefly
explained in the following table:

Program Description

G3ConfigApp The

G3ConfigApp

program allows you to configure the MegaRAC G3 card from the host

system or from a client system.

WinCuriG3 The

WinCuriG3

program is a command prompt-based program that you can use to configure

the MegaRAC G3 card. It allows you all the functionality of both the Internet browser-based

Remote Access Companion for MegaRAC G3

and the

G3ConfigApp

program.

HostHeartbeat HostHeartbeat

is

installed as a service in Windows. It is used to tell whether the operating

system on the host system is operating or not. It can also detect whether the operating system
was shutdown normally or abruptly.

Floppy Image
Creator

Floppy Image Creator

allows you to create bootable floppy image files that you can use to

boot the MegaRAC G3 card from.

Platform
Management
Configuration
Program (PMCP)

Platform Management Configuration Program (PMCP)

allows you to create SDR and Soft

Processor (SP) Files for your specific motherboard or server board.

Remote Recovery
Application (RRA)

The

Remote Recovery Application (RRA)

is a recovery tool that can be executed from a

remote client system located on the same network as the MegaRAC G3 card. You can use it
to recover a failed flash attempt.

Note:

You must physically set the MegaRAC G3 card you want to recover into

Recovery

Mode

. To do this, simply short pins two and three on jumper JP12 on your MegaRAC

G3 card.

Note:

Your MegaRAC G3 card must be write enabled before you can flash an image to it.
Confirm that pins one and two on jumper JP11 are shorted on your MegaRAC G3
card.

Note:

The firmware upgrade process is a crucial operation. Make sure that the chances of a
power or connectivity loss are minimal when performing this operation.

RacTrendsSeek
Locator

In order to configure your MegaRAC G3 card completely, you must access the MegaRAC G3
from another system on the same network. To do this, you must know the MegaRAC G3
card’s IP address. If you have installed the MegaRAC G3 on a network that uses DHCP, you
can search the network for the MegaRAC G3 card. To locate and find out its IP address, you
can use

RacTrendsSeek Locator

.

Cont’d

«
...
21
22
23
24
25
...
»

Summary of Contents for MegaRAC G3
























































































































































Reviews:

No comments

Related manuals for MegaRAC G3

Brand: 3Com Pages: 8

Brand: Udoo Pages: 7

WS-650 lite Series

Brand: Laurell Pages: 84

RocketLink-G 3088/I

Brand: Patton electronics Pages: 61

iW-RainboW-G30D

Brand: iWave Pages: 89

Brand: Patton electronics Pages: 13

DataPlot CB1224

Brand: B-G Instruments Pages: 4

Brand: CNC4PC Pages: 11

ipRocketLink IAD 3086

Brand: Patton electronics Pages: 12

Brand: Aviosys Pages: 77

Protection Board R0E330850ACBP0

Brand: Renesas Pages: 8

Brand: XtendLan Pages: 17

Brand: ANTAIRA Pages: 6

Brand: ICP DAS USA Pages: 62

EK-FC670 GTX Series

Brand: ekwb Pages: 2

Brand: ADTRAN Pages: 4

mvHYPERION-32R16

Brand: Matrix Vision Pages: 148

Brand: Abov Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands