American Megatrends MegaRAC G3 User Manual Download Page 130

Page: 130 / 151

MegaRAC G3 User’s Guide

122

MegaRAC G3 Card Remote Recovery Application (RRA),

Continued

Step Description

Left click the

Card Settings

button to begin.

The

Active Cards in Recovery Mode

screen appears and starts to search for MegaRAC G3 cards in

Recovery Mode

Left click the MegaRAC G3 card’s MAC address that you want to configure.

The

Active Cards in Recovery Mode

buttons are explained in the table below:

Button Description

Stop The

Stop

button allows you to stop searching the network for active cards in

Recovery

Mode

Refresh The

Refresh

button allows you to start searching the network again for MegaRAC G3

cards’ MAC addresses in

Recovery Mode

Select The

Select

button allows you to specify the highlighted MegaRAC G3 card’s settings.

You can specify the MegaRAC G3 card’s MAC, IP, Network Mask, and Gateway
addresses as shown in the following step.

Cancel The

Cancel

button allows you to cancel any new settings that are not saved.

Cont’d

Summary of Contents for MegaRAC G3
























































































































































Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands

American Megatrends MegaRAC G3, User Manual

Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands