American Megatrends MegaRAC G3 User Manual Download Page 147

Page: 147 / 151

Appendix H : Host System USB Mouse and Keyboard Considerations for Linux 7.x

139

Appendix H

Host System USB Mouse and
Keyboard Considerations for
Linux 7.x

Overview

This appendix describes how to set up the USB keyboard and mouse on the host system
running RedHat Linux 7.x so that they can be redirected.

Note:

For RedHat Linux 8.x, disregard these instructions.

File Description

This package contains two files as described below:

MOUSEC~1 RPM 118,299 11-28-01 16:43

mouseconfig-4.22-1.i386.rpm

README.PDF

this

file

The first file can be downloaded from the following website:

http://www.redhat.com/support/errata/RHBA-2001-062.html

Check Your AMIBIOS Settings

Check your system BIOS to verify that the

OnBoard USB

and

Legacy USB

options are

Enabled

. If not, the USB devices cannot function.

USB Keyboard

You will be able to redirect the keyboard and use the keyboard on the host system at the
same time.

Note:

LILO is not USB aware. The system BIOS must have USB keyboard support. If not, you
cannot use the redirected keyboard to select a different boot image.

Summary of Contents for MegaRAC G3
























































































































































Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands

American Megatrends MegaRAC G3, User Manual

Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands