American Megatrends MegaRAC G3 User Manual Download Page 132

Page: 132 / 151

MegaRAC G3 User’s Guide

124

MegaRAC G3 Card Remote Recovery Application (RRA),

Continued

Step Description

The

Flash Related Operation

screen appears.

The

Flash Related Operation

buttons are explained in the table below:

Button Description

Get Flash Information
Button

Left click the

Get Flash Information

button to get flash information.

Program (Write) Flash
Button

Left click the

Program (Write) Flash

button to continue with the flashing

function.

Back Button

Left click the

Back

button to go to the previous screen.

When you left click the

Get Flash Information

button, the

Flash Information

screen appears.

Note:

Pay special attention to the size of the

Erase Block Size (in Kbytes)

. You need to select the

correct

Flash Block Size

in the

Program (Write) Flash

section.

Cont’d

Summary of Contents for MegaRAC G3
























































































































































Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands

American Megatrends MegaRAC G3, User Manual

Search results

Summary of Contents for MegaRAC G3

Reviews:

Related manuals for MegaRAC G3

Brands by name

Popular brands