AMATI 25076 Manual Download Page 45

Page: 45 / 56

Bismarck

173

967

The picture shows the view of the admiral’s bridge and the searchlight deck with

the positioning of accessories 2532, 2576, 2551, 2574 on the port side of the model.

971

Remove ten pieces 2578 and 2579 of the aerators from

sprue P25 and ten gratings 1472 from sheet 1561. Bend the

gratings to 90° and glue them to the side wall of columns

2578, 2579. Prepare a total of five aerators for the starboard

side and five for the port side.

972-973

With Ral 7001 paint, colour the ten aerators completely. Once dry, glue the five aerators 2578 to the

redoubt of the heavy weaponry tower on the starboard side of the bow superstructure. Identify their position

by referring to the accessories on the arched wall below. Rotate the model and in the same way glue the other

five aerators 2579 to the redoubt of the heavy weaponry tower on the port side. Also in this case, you can

use the portholes of the underlying wall as a reference to identify the position of the aerators on the redoubt.

Take two white ring buoys 4000/03 (step 882) and glue one on each side in the position shown in the picture.

969

The picture shows the view from the stern of the foremast tunnel and the central

shooting direction station with the positioning of accessories 2575 and 2333.

970

Now equip the funnel platform with two searchlights 2547 and two cannons

2510 (step 888). Orient these elements as shown in the picture.

968

Move to the foremast foretop gallery and glue ladder 1469 step 965, two radio

compasses 2532 and four gunsight telescopes 2575 (step 963). Move to the central

station floor and glue three searchlights 2333 that you will have to separate from

sprue P36 with a cutter. Also observe the following picture to identify the correct posi-

tion and orientation of these elements.

967

970

968

971

969

972

973

2537

2551

2532

2575

2532

1469

2575

2333

2574

2576

2532

2510

1472

2578

2579

1472

2547

2578

2579

4000/03

2579

2578

STARBOARD

PORT

4000/03

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands