AMATI 25076 Manual Download Page 14

Page: 14 / 56

Bismarck

250

Rotate the structure and replicate the assembly of the arches on the port side using plastic pieces 2315, 2317. See also the

next step.

252

Now remove the two decks 128 and 129 from laser sheet 3556A, which will be inserted from above onto the structure.

253

Perform tests without glue to check the alignment of the pieces. Spread a layer of wood glue on the upper edges of the bow

crossbeams and glue deck 128; then move to the stern and spread a layer of glue on the upper edges of the wooden walls of the

cabins; then glue deck 129 in place. The picture in detail shows the upside-down structure highlighting deck 129 which protrudes

beyond the outer edge of the cabins.

251

The picture shows the inverted structure complete with the assembly of the four plastic arches.

250

252

251

253

2315

2317

2315

2314

2316

2317

2316

129

128

BOW

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands