AMATI 25076 Manual Download Page 38

Page: 38 / 56

Bismarck

142

742

Glue the two structures you just assembled in the joints on platform 1245. Then

prepare twenty-four pillars 1252 which you can find on sheet 1559.

747

Insert the two walls 1255 into the joints of pieces 1256 and into the joints on

platform 1245; then glue. Prepare the other four pillars 1252 and two other front

pieces 1253 which you can always find on the same sheet 1559.

744

Rotate the platform and prepare front pieces 1253, 1254 (sheet 1559).

746

Rotate the structure again and prepare pieces 1255 (x2) and 1256 (x2) (sheet

1559) which will be assembled in the other joints which are still free on the platform.

743

Insert vertical pillars 1252 into the joints of platform 1245 and glue 13 of them

on the left rack and 11 of them on the right rack.

745

Glue the four pieces 1253 (x2) and 1254 (x2) in the joints at the head of the

racks.

747

742

745

743

746

744

1252(x24)

1249

1245

1254

1253

1255

1256

1255

1256

1253

1252

1253

1255

1254

1253

1252

(x3)

1252(x2)

1252(x3)

1246

1252(x4)

1252(x3)

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands