AMATI 25076 Manual Download Page 43

Page: 43 / 56

Bismarck

169

2542

2517

1445

2517

2544

2525

2526

2543

1446

2510

1437

2518

2510

1437

2536

2517

2503

2517

938

Remove from sprues P13, P20 base 2545, support 2546, dish

2547 and from sprue P18 the transparent glass 2548 of one of the five

searchlights that you will have to prepare in these assembly steps.

939

Assemble support 2546 in the side holes of dish 2547;

then glue.

940

Insert the dish with support as shown in the

picture in the upper dowel of base 2545 and glue.

943-944

Glue ladder 1445 (step 930), two containers 2518

(P26), the two piles of life rafts 2536 (step 920), two can-

nons 2510 and two 1437, one on each side. Then move to

the side walls of the 1st and 2nd level and glue the Q lad-

ders, two containers 2503 (step 883) and four containers

2517 (P26), two ladders 1446 and three life jackets 4000/03

one on the port side and two on the starboard one.

941

Before gluing the transparent glass to the dish, prepare four more

searchlights with base 2545, support 2546 and dish 2547 and paint all

five of them in Ral 7001 grey. Once dry, you can fix the plates to the

searchlight dishes.

942

Now that you have prepared several accessories, you can begin to fix them on the decks of the

stern superstructure. Before gluing them, you have to paint the elements still to be coloured in Ral 7001

grey. Once dry, you can glue cabinet 2525 and aerator 2526 (sprue P25) to the forecastle deck against

the turret wall in the position shown. Move to the upper deck and glue six containers 2517 (P26), three

on each side, rangefinder 2542 (P27) on the turret, a B

cable reel to the side of the turret, and aerators

2543-2544 (P25) on the edge of the deck. Orient all these elements as shown in the picture and identify

their position drawn on the deck claddings.

938

942

940

939

943

941

944

2547

2547 (x5)

2545

2546

2548

2547

2548

2545

2546

4000/03

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands