AMATI 25076 Manual Download Page 24

Page: 24 / 56

Bismarck

408

Complete with ladder 815, which must be glued inclined towards the inside of

the structure. The starboard side ladder is complete.

413

Turn the turret over to its correct position and bend railing 822 on three sides

in order to adapt it to the edge indicated by the red arrow on the back of the turret.

Observe the picture in detail and glue railing 822 in place.

410

Replicate the assembly on the port side of the admiral’s bridge symmetrically.

412

Glue the two brackets 819 inclined outwards on the protrusions under the bridge

(see red arrows, previous step) and rod 820 in the centre with the eyelet placed

outwards. Take the two 821 railings and glue them along the inclined edges of the

admiral’s bridge oriented as shown in the picture. Place the thicker edge of the railing

against the bent edge of the plank.

409

Move under the other circular platform of the admiral’s bridge and prepare the

pieces from 816 to 818 (sheet 1557) for the assembly of the ladder on the port side.

411

With the turret upside down, move under the front of the admiral’s bridge and

prepare brackets 819 (x2), cable tension rod 820 and three railings 821 (x2) and 822

(sheet 1557).

408

411

409

412

410

413

815

813

816

819

821

822

820

819

821

822

818

817

816

818

817

814

BOW

2345

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands