AMATI 25076 Manual Download Page 16

Page: 16 / 56

Bismarck

319

Remove from sprue P23 the two halves of support cylinder

2318 (x2), the two halves of the base of dome 2319 (x2) and

cap 2320 with the range finders; you will use them to prepare

one of the two anti-aircraft shooting positions, which will be

assembled on the sides of the bow superstructure.

325

Remove the two prepared turrets from the mod-

el and keep them aside together with the superstruc-

ture; they will be glued later.

321

Glue dome 2320 on base 2319, placing

the two range finders in the upper lateral

joints of the base. Remove one of the two

protrusions on the sides of the cylinder with a

cutter, leaving only one.

322

Take the bow superstructure and provisionally apply the cylinder in the semicir-

cular cut out located on the port side of the second level deck. Position it so that the

protrusion on the cylinder points towards the bow and at an angle almost with respect

to the handrail (red arrow). Do not glue!

324

Repeat the same assembly procedure for the second shooting position which will be assembled on the port side of the

superstructure. Use the other components which you can find on sprue P23: 2318 (x2), 2319 (x2) and 2320.

320

Join without glue the two halves of cylinder 2318

and base 2319; after checking that they coincide per-

fectly, fix them definitively with superglue.

323

Hold the cylinder in position and glue cap 2319-2320 on turret 2318,

placing the range finders parallel to the rear of the structure and the small

dowel on the cap (red arrow) oriented towards the stern. Warning: do not

glue the turret to the structure.

2318

2320

2319

2318

2319

2320

2318

2319

2320

2319

2320

319

323

320

324

322

321

325

BOW

do not glue

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands