AMATI 25076 Manual Download Page 30

Page: 30 / 56

Bismarck

110

583

Glue the platform to the funnel; if necessary, finish the internal curve of the

platform with sandpaper to adapt it to the wall of the funnel.

588

Remove the three cabinets 2421a and 2421b (x2) from sprue P25, which you will

have to glue on the navigation deck against the side wall of the tower. As you can see,

the rear wall of the three cabinets is curved to adapt to that of the tower. Observe the

picture above and after painted them in Ral 7001 grey, glue them to the sides of the

tower in the position shown.

585

The picture shows the assembly of cable 1008 with bracket 1009 seen from

another angle.

587

Once dry, take the tower structure and glue it on the upper navigation deck, as

shown in the picture.

584

Now that the platform is glued in position, remove cable 1008 and bracket 1009

from sheet 1557b; bend the upper end of cable to 90° as shown in the detail above

and paint the two components in Ral 7001 grey. Insert cable 1008 in the appropriate

recesses of the platforms (indicated by the red arrows) up to the rear base of the

funnel. Glue cable and bracket in place as shown in the picture.

586

Now proceed to colour the other previously prepared structures. With Ral 7001

grey, completely paint the structure of the tower with the admiral’s bridge; gallery

2347; the central shooting station and the central shooting tower. Once dry, brush

with Ral 7024 on the floor of the admiral’s bridge and gallery. With the same dark

grey, paint the attic of the shooting station, the roof and the antenna of the central

turret excluding the profile on the edge. Paint the radar device in matt black. Observe

the picture to identify the colouring areas.

583

586

584

587

585

588

1008

1009

RAL 7001

RAL 7024

BLACK

RAL 7024

2421a

2421b

2421a

BOW

2347

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands