AMATI 25076 Manual Download Page 40

Page: 40 / 56

Bismarck

144

2466

2469

754

Remove accessories 2469, 2467, 2466, 2468 from sprue P25, watchtower P48

and wall 1270 from sheet 1559.

758-759

Remove the pieces shown in the picture for the assembly of the crow’s nest and the platform of the mainmast from

sheet 1559. Lift the four side walls of crow’s nest 1273 upwards along the engraved marks; then glue them together. Insert the

three shelves, 1276 central and 1277 (x2) on the sides of platform 1275 and fix them as shown in the picture.

756

The picture above shows a view of the watchtower from the opposite side,

aligned with the side walls and the semicircular profile on the platform; it determines

the position of the mainmast. Fix piece 2469 over the watchtower as shown in the

picture.

755

Following the picture above, fix front wall 1270 to the side of the platform; the

two cabinets 1247, 1248 inside walls 1264, 1265 and watchtower 2466 in the centre

of the platform.

757

Now move on to the assembly of the mainmast. Cut the 2750/04 copper tube (Ø 4mm) to a length of 130mm and with a file,

sand one end in order to obtain the shape shown in the photo and in the drawing. Cut two 65mm and 55mm long sections of the

2524/03 wooden dowel (Ø 3mm); then, with abrasive paper taper and gradually round off one end of the 65mm bar, so that its

diameter measures 1.5mm. Mark in pencil on the copper tube the position of the accessories that you will have to assemble on the

spindle of the mast and on the section of 65mm wooden dowel mark the dimensions shown in the drawing. Try inserting without

glue the 65mm wooden dowel in the upper hole of the copper tube, up to the lower mark and the 55mm dowel section in the lower

hole; always without gluing.

758

759

754

757

755

756

2467

1265

1264

2468

2466

1270

1273

1274

2750/04

2524/03

1276

1277

1275

1276

1277

1274

1273

Ø 4mm

do not glue

1270

2468

2467

2469

2466

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands