AMATI 25076 Manual Download

Page: 35 / 56

Bismarck

139

723

Couple the two plates 1214 on each piece 1212 and 1213 and glue. Rotate the

structure and glue the two junction boxes 1213-1214, 1212-1213 on the inside of

railing 1210, oriented as shown in the picture.

728

Rotate the structure and prepare the other accessories depicted

in the picture and which you can find on sheet 1559. Separate the

two searchlights 2333 from sprue P36 with a cutter.

729

Close the structure with claddings 1218 and 1222. Fix the accesso-

ries to wall 1218: ladder 1219 in the centre vertically, hatch 1220 aligned

with the relief engraved on the wall and under ladder 1221. Move to the

roof and fix the two searchlights 2333 aligned with the circular drawings

engraved on cladding 1222.

725

Position the newly assembled structure on the stern superstructure, check the alignments

and glue arranging frame 1211 of the rack towards the stern.

727

Round the wall in the central part until it

adapts to the front curve of structure 207. Try it

without glue, then glue. Fix door 1217 aligned

with the hinges engraved on the wall.

724

Take the turret of shooting direction station 2451 and fix it to the centre

of platform 197. Align padeye 1199 on the turret above the platform frame.

726

Retrieve structure 207 of the rear control station assem-

bled in step 654 and remove covering wall 1216 and door

1217 from sheet 1559.

723

726

724

727

725

728

729

1211

1209

1222

2333

1218

1222

1219

1220

1221

1218

1216

207

1217

1216

1212-1214

1213-1214

1210

1214

1213

1212

BOW

207

BOW

1199

197

2451

1211

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Related manuals for 25076

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Related manuals for 25076

Brands by name

Popular brands