AMATI 25076 Manual Download Page 33

Page: 33 / 56

Bismarck

137

710

Try to insert bridge 2450 in the opening on the deck between claddings 193-195

and the four side railings. If necessary, slightly sand the walls of the bridge with sand-

paper at the points of contact with the railings. Once you have checked the correct

insertion, fix it to the structure with superglue.

715

Now prepare the other turret of the shooting direction station D, the highest one.

Join the two plastic components 2455-2456 (P49) and remove the accessories shown

in the photo from sheet 1559 and sprue P25.

712

Now that you have returned the position of the elements to the turret, you can

remove ladder 1196, two drainage pipes 1197, 1198, padeye 1199, railing 1200 and

elements 2453 (x2) and 2454 (x2) from sprue P25. Temporarily put cover 197 aside.

Model the railing by wrapping it around the plastic template P2.

714

On the left side of ladder 1196, glue electrical panel 2454 and cabinet 2453;

next to the 1198 tube glue the second electrical panel 2454 and the other the cabinet

2453 symmetrically. Finally glue railing 1200 along the edge of the flange. Keep aside

the turret, which will be fixed to the superstructure at a later time.

711

Now prepare the turret of the shooting direction station C. Assemble platform 2452

on turret 2451 (P50). Warning: the stern superstructure is made up of two similar turrets;

take the lower one and with the joint in the flange. Draw the centre line in pencil on

piece 197 (step 643); position the turret in the centre of the piece and orient the joint

on position A. Mark in pencil along the turret cylinder positions A and B of the drainage

pipes which you will assemble in the following steps.

713

Glue ladder 1196 vertically along the turret aligned with the joint in the flange.

Fasten the vertical part of tube 1197 to the right of the ladder, the upper end instead

curves to the left above the ladder and ends under the flange (see detail on the left).

In the same way, glue pipe 1198 vertically along the turret in position B (see detail on

the right). With

.5mm drill bit, drill a hole in the cylinder in the centre between

the two pipes and glue padeye 1199.

710

713

711

712

715

714

196

2450

hole

Ø 0.5mm

120°

2451

2452

2451

197

1196

1197

1196

1198

1199

1197

1196

1198

2454

2453

2456

2455

2456

2455

2457

2454

2453

2454

1200

1201

1202

1203

1205

1204

195

193

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands