AMATI 25076 Manual Download Page 17

Page: 17 / 56

Bismarck

362

Now move on to setting up the front control station that

you have assembled on page 53. Remove from sheet 1556 the

covering walls and accessories shown in the picture.

368

Also fill the crack on the roof with putty and sand with

sandpaper.

369

Take the accessories prepared in step 362 and glue them

to the sides of the station walls in the position shown in the

pictures.

364

Glue wall 781 to the structure and bend the two walls 782

and 783 to adapt them to the front of the structure. The three

side wings of piece 783 serve as spacers to correctly position

the piece on the structure.

365

Glue claddings 782 and 783 to the structure as shown

in the picture. Take roofs 784 and 785, which you will have to

glue over the structure.

367

At this point, fill and level the cracks and imperfections

of the structure with putty and sandpaper in order to level the

walls.

363

Take cladding 781 and shape it according to the curved

profile of the station structure. Observe the next picture to find

its positioning.

366

Position roof 784 aligned with walls 781, 783 and roof

785 aligned with walls 781, 782.

362

366

363

367

364

365

368

369

781

782

784

781

783

782

785

783

782

783

781

785

784

783

787

782

788

786

788

785

784

788

786

788

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands