AMATI 25076 Manual Download Page 23

Page: 23 / 56

Bismarck

402

Glue railings 808 (x2), 809 (x2) and railing 810 aligned in the centre and under

the platform gangway (see detail). The front part must serve as support for piece 811;

glue the latter to the centre.

From this moment, we will indicate the resulting structure of the platform with num-

ber 803.

407

Slightly close the sides of the two crossbars inwards, just enough to receive

piece 814, which can also be bended and glued in position as shown in the picture

and the detail.

404

Observe the picture to correctly orient the pieces; then glue.

406

Fasten the two crossbars 813 and 812 in the joints of the lower part of the plat-

form by placing the shorter crossbar (812) towards the stern.

403

Now that the platform is ready, you can glue it to the tower between the admi-

ral’s bridge and the searchlight deck.

405

Now prepare the two moveable ladders which will be placed under the lateral

protruding platforms of the admiral’s bridge. Prepare the photo-etched pieces from

812 to 815 (sheet 1557) of the moveable ladder of the bridge on the starboard side.

407

402

405

403

406

404

812

2345

813

815

814

812

813

814

813

BOW

809

810

811

803

808

BOW

2345

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands