AMATI 25076 Manual Download

Page: 19 / 56

Bismarck

376

Take the three prepared structures: the front control sta-

tion, the lower navigation deck and the bridge, lay them on

your worktop oriented as shown in the picture.

382

Glue the two range finders 2363 and 2364 to the sides of the turret

with the protruding lenses oriented towards the bow. Prepare the acces-

sories shown in the picture for the preparation of the turret which you can

find on sheet 1557.

383

Glue profile 790 along the edge of the turret

roof.

378

Always insert without gluing the control station in the cen-

tral joint of the deck; it will serve you as a guide to correct the

position of deck 2353.

379

We advise you not to glue the structures but only

check their position before proceeding with the final

painting; this will be done later. Put these elements aside.

381

Join turret 2361 to base 2360 and insert piece 2362 in

the hole on the roof of the turret; then glue.

377

Perform tests without glue. Position the deck aligned with the

front walls of the underlying superstructure and the side railings.

380

Remove the components of the front shooting direction

turret from sprue P35 and lay them on your worktop orient-

ed as shown in the picture above. This turret will be prepared

following the next assembly steps and assembled later on the

front control station.

382

383

376

380

377

381

378

379

2353

2361

2360

794

790

791

793

792

2362

2361

2362

2363

2364

BOW

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Related manuals for 25076

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Related manuals for 25076

Brands by name

Popular brands