AMATI 25076 Manual Download

Page: 21 / 56

Bismarck

390

Take sprue P40 and remove the pieces shown in the picture above; they will be

used for the assembly of the tower structure which will be assembled on the bow

superstructure.

395

Take plastic component 2346, the searchlight deck (sprue P41) which will be

glued on the front relief of the tower (red arrow). Smooth any imperfection with

sandpaper.

392

Glue piece 2344 on the back of the tower in the position highlighted in the

detail. Take plastic piece 2345 of the admiral’s bridge (sprue P41) which will be glued

to the tower.

394

Once the correct position has been identified, definitively glue the bridge to the

tower.

391

Lay the two halves of tower 2341 and 2342 on your worktop, then couple them

without glue. After verifying that the two parts coincide perfectly, fix them definitively

with superglue. Smooth at the joints with sandpaper. Close the opening on the front

of the tower with window 2343 and glue (see detail above).

393

To find the correct position of bridge 2345, observe the picture above which

shows the lateral protrusions placed on the lower part of the tower; they determine

the position of bridge 2345.

391

390

393

394

392

395

2341

2342

2341

2342

2343

2345

2344

2345

2346

2344

2342

2343

BOW

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Related manuals for 25076

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Related manuals for 25076

Brands by name

Popular brands