AMATI 25076 Manual Download Page 39

Page: 39 / 56

Bismarck

143

748

Glue on each of the two walls 1255, two vertical pillars 1252, and a front piece

1253, as shown in the picture.

753

The picture above shows in detail the assembly of the side plat-

form of the signal station.

752

Insert the two front walls 1264, 1265 into the joints and glue them. Bend the railings 1266 and

1268 outwards to 90°, in the engraved marks and glue them to the side platforms. Subsequently,

always bend the other two railings 1267, 1269 outwards and glue them in the position shown in

the picture.

749

Rotate the structure and prepare the side walls with support feet 1257 and 1258

(sheet 1559). Bend the lower ends of sides 1257 and 1258 inwards to 90°, along the

engraved marks; then glue them to the sides of the structure using the joints. bend

the railing of wall 1259 as shown in detail and glue it to the edge of platform 1254.

750

Rotate the structure and prepare pieces 1260, 1261, 1262, 1263 always from the

sheet 1559, in order to create the two side platforms.

751

Glue the first two pieces 1260, 1262 to the side walls of the signal station as

shown. Later, also fixed the small platforms 1261, 1263. Remove the two walls 1264,

1265 and the railings for the side platforms 1266, 1267, 1268, 1269 from sheet 1559.

748

751

749

752

750

753

1252

1255

1252

1253

1252

1255

1252

1257

1258

1262

1260

1261

1263

1265

1266

1267

1269

1268

1266

1269

1264

1265

1260

1261

1259

1254

1259

1257

Bend here

Summary of Contents for 25076

























































Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands

AMATI 25076, Manual

Search results

Summary of Contents for 25076

Reviews:

Brands by name

Popular brands