background image

MN-36580 (Rev. 2) 01/16 • Quickchillers • 2

c a u t I o n

Used to indicate the presence of a hazard that 
can or will cause minor personal injury, property 
damage, or a potential unsafe practice if the 
warning included with this symbol is ignored.

c a u t I o n

Used to indicate the presence of a 
hazard that can or will cause minor or 
moderate personal injury or property 
damage if the warning included with 
this symbol is ignored. 

D a n g e r

Used to indicate the presence of 
a hazard that WILL cause severe 
personal injury, death, or substantial 
property damage if the warning 
included with this symbol is ignored.

W a r n I n g

Used to indicate the presence of 
a hazard that CAN cause personal 
injury, possible death, or major 
property damage if the warning 
included with this symbol is ignored.

• 

This appliance is intended to chill or freeze foods 
for the purpose of human consumption.  No other 
use for this appliance is authorized and is therefore 
considered dangerous. 

• 

This appliance is intended for use in commercial 
establishments where all operators are familiar 
with the purpose, limitations, and associated 
hazards of this appliance.  Operating instructions 
and warnings must be read and understood by 
all operators and users. We recommend regular 
training of your staff to avoid the risk of accident 
or damage to the unit. Operators must also receive 
regular safety instructions.

• 

Any troubleshooting guides, component views, and 
parts lists included in this manual are for general 
reference only and are intended for use by qualified 
and trained technicians.

• 

This manual should be considered a permanent part 
of this appliance.  This manual and all supplied 
instructions, diagrams, schematics, parts lists, 
notices, and labels must remain with the appliance 
if the item is sold or moved to another location.

N o t I C E :

    

Used to notify personnel of 
installation, operation, or 
maintenance information that is 
important but not hazard related.

safety proceDures
anD precautIons

Knowledge of proper procedures is essential to the 
safe operation of electrically and/or gas energized 
equipment.  In accordance with generally accepted 
product safety labeling guidelines for potential 
hazards, the following signal words and symbols 
may be used throughout this manual.

Used to indicate that referral to 
operating instructions is a mandatory 
action. If not followed the operator 
could suffer personal injury.

Used to indicate that referral to 
operating instructions is recommended 
to understand operation of equipment. 

N o t I C E

For equipment delivered for use 
in any location regulated by the 
following directive:
DO NOT dispose of electrical or 
electronic equipment with other 
municipal waste. 

Safety Procedures and Precautions

Summary of Contents for Quickchiller QC2-100




























































Reviews: