Allen-Bradley 22-COMM-E FRN 1.xxx User Manual Download Page 147 | Manualshive

Page: 147 / 166

background image

EtherNet/IP Objects

C-35

Instance Attributes (Continued)

Services

Ethernet Link Object

(Continued)

Attribute
ID

Access
Rule

Name

Data Type

Description

4

Get

Interface
Counters

STRUCT of:

UDINT
UDINT
UDINT
UDINT
UDINT
UDINT
UDINT
UDINT
UDINT
UDINT
UDINT

Octets received
Unicast packets received
Non-unicast packets received
Inbound packets received but discarded
Inbound packets with errors (not discarded)
Inbound packets with unknown protocol
Octets sent
Unicast packets sent
Non-unicast packets sent
Outbound packets discarded
Outbound packets with errors

5

Get

Media
Counters

STRUCT of:

UDINT
UDINT
UDINT
UDINT
UDINT
UDINT
UDINT
UDINT
UDINT
UDINT
UDINT
UDINT

RX = Received, TX = Transmitted
RX frames not having integral number of octets long
RX frames not passing FCS check
TX frames having one collision
TX frames having multiple collisions
Number of times of SQE test error message
TX Frames delayed first attempt by busy medium
Collisions detected later than 512 bit-times in trans.
TX frames failing due to excessive collisions
TX frames failing due to intern MAC sublayer TX error
Times of carrier sense condition loss during trans.
RX frames exceeding the maximum frame size
RX frames failing due to intern MAC sublayer RX error

Service Code

Implemented for:

Service Name

Class

Instance

0x0E

Yes

Yes

Get_Attribute_Single

0x4C

No

Yes

Get_and_Clear

«
...
145
146
147
148
149
...
»

Summary of Contents for 22-COMM-E FRN 1.xxx







































































































































































Reviews:

No comments

Related manuals for 22-COMM-E FRN 1.xxx

SPAS 2400/LC + MU

Brand: VOLTCRAFT Pages: 4

Brand: Inateck Pages: 26

Brand: Allied Telesis Pages: 2

Brand: AMS Pages: 13

Brand: Inteltronic Pages: 1

Brand: Rocom Pages: 2

Brand: Digitus Pages: 30

Brand: Atheros Pages: 39

Brand: MSI Pages: 53

Brand: AUDAC Pages: 12

Brand: Trevi Pages: 40

Brand: Sony Pages: 40

Brand: Wisenet Pages: 6

Brand: SICK Pages: 32

Brand: Schwaiger Pages: 2

Brand: BECKWITH ELECTRIC Pages: 25

Brand: essentiel b Pages: 10

Brand: ActionTec Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands