AJA FS-HDR Installation And Operation Manual Download

Page: 86 / 129

FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 86 www.aja.com

1.6 Custom Right Crop

This parameter changes the Right picture crop position.

100% (default)

+10.0% to +100.0%

Maintains the normal right side position of the selected format.

Enables changing the right side position.

1.7 Custom Top Crop

This parameter changes the Top picture crop position.

100% (default)

+10.0% to +100.0%

Maintains the normal top position of the selected format.

Enables changing the top position.

1.8 Custom Bottom Crop

This parameter changes the bottom picture crop position.

100% (default)

+10.0% to +100.0%

Maintains the normal bottom position of the selected format.

Enables changing the bottom position.

Region of Interest (ROI)

The Region of Interest parameters select a portion of the input picture that will

be used for scaling and/or positioning. The selected area can then be scaled to

a standard pillarbox or letterbox size and shape (On Square), or it can be set to a

full screen input image (On Full). On Full may cause image distortion if it is used to

expand an odd-shaped region of interest to full screen.

NOTE: The ROI feature is not available in Single Channel Mode if both the inputs and

outputs are UltraHD/4K.

The ROI Setup mode allows you to preview the edges of your selected Region Of

Interest as you set it up. After selecting the desired region using the Setup Cursor,

you can take the region to air by setting Region Of Interest to On Square or On

Full.
The Setup mode is not required to operate the ROI feature. The edges of the

Region Of Interest can also be adjusted while in On Square or On Full modes

2.0 Region of Interest

This parameter turns the Region of Interest settings On or Off. When enabled,

the ROI Left, Right, Top, and Bottom controls define the rectangular shape and

position of the ROI.

Off (default)

Setup

On Square

On Full

Turns off the ROI feature.

Enables ROI cursor.

Enables ROI and sets video to a pillarbox or letterbox shape.

Enables ROI, and expands the ROI area to full screen.

Interactions occur between ROI settings and other parameters:

• The Region of Interest menu is not displayed when Active Format Description

(AFD) is in control of the Conversion Mode.

• Custom Size and Position settings work interactively with ROI, but Custom

Crop settings are disabled. Custom Size/Pos is also temporarily disabled while

in the ROI Setup mode.

Summary of Contents for FS-HDR


































































































































Search results

Summary of Contents for FS-HDR

Reviews:

Related manuals for FS-HDR

Brands by name

Popular brands

AJA FS-HDR, Installation And Operation Manual

Search results

Summary of Contents for FS-HDR

Reviews:

Related manuals for FS-HDR

Brands by name

Popular brands