AJA FS-HDR Installation And Operation Manual Download Page 43

Page: 43 / 129

FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 43 www.aja.com

HD Video Camera to UltraHD HDR Live Production

The following workflow demonstrates feeding an HD video camera signal to an

UltraHD HDR capable video switcher through the FS-HDR for a live production. In

this example a Canon camera's HD Log 2 output is converted to UltraHD Hybrid

Log Gamma.

Figure 23. Single Channel Mode, HD Up Conversion to UltraHD HDR

SDI Out 7 SFP
SDI Out 8 SFP

SDI Out 5 SFP

SDI Out 6 SFP

SDI Out 4 BNC

SDI Out 1 BNC

SDI Out 2 BNC

SDI Out 3 BNC

4K/UHD

Video Processor with

Colorfront Engine

SDI In 1 BNC

SDI In 2 BNC

SDI In 3 BNC

SDI In 4 BNC

SDI In 5 SFP

SDI In 6 SFP

SDI In 7 SFP

SDI In 8 SFP

Camera Signal

1920 x1080i

59.94 (SDR)

Signal to Video Switcher

Up-Converted to

Quad Link UltraHD

3840x2160p 59.94 (HLG)

Signal Up-Converted to

Quad Link UltraHD

3840x2160p 59.94 (HLG)

(Requires optional SFP

modules)

Camera HD Up-Conversion to UltraHD with HDR

Single Channel Mode

Table 2. Menu Settings for Single Channel Mode, Up Conversion

Channel Select Button Video Button Menu Name

Setting

VID1

INPUT

1 Input

SDI1

VID1

INPUT

2.1 Dynamic Range&Gamut Canon Log 2 (match to camera)

VID1

FORMAT

1 Output Format

UHD2160p5994

VID1

FORMAT

2.1 Dynamic Range&Gamut Hybrid Log Gamma BT.2100

VID1

FORMAT

2.2 Dynamic Range Clamp

No Clamp (default)

VID1

FORMAT

3.0 Link Cfg SDI1-4

Quad Link LvlA

VID1

FORMAT

4.0 Link Cfg SDI5-8

Quad Link LvlA

VID1

FORMAT

5.0 Output Image Mapping Quadrant or 2SI (as required)

Setup

• Ensure the FS-HDR is receiving a valid reference signal. Connect a 1080i59.94

HD tri-level sync signal to one of the Ref Loop BNC connectors, and terminate

the other Ref Loop BNC connector.

• Configure the camera (for example, SDI 1080i59.94 Canon Log 2)
• Connect the camera's SDI output connector to the SDI1 input on the rear of

the FS-HDR. Once connected the FS-HDR front panel VID IN LED will light.

• Connect the four FS-HDR SDI1-4 video output BNC connectors to a UltraHD

video production switcher that supports Hybrid Log Gamma.

• View the FS-HDR SDI output signal on a compatible HDR display.

Summary of Contents for FS-HDR


































































































































Search results

Summary of Contents for FS-HDR

Reviews:

Related manuals for FS-HDR

Brands by name

Popular brands

AJA FS-HDR, Installation And Operation Manual

Search results

Summary of Contents for FS-HDR

Reviews:

Related manuals for FS-HDR

Brands by name

Popular brands