AJA FS-HDR Installation And Operation Manual Download

Page: 63 / 129

FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 63 www.aja.com

NOTE: To eliminate trailing characters to shorten an existing system name, overwrite

them with a hyphen (-) or space.

2 FS-HDR Mode

Selects whether the FS-HDR will operate in Four Channel or Single Channel mode.

Pressing the ADJUST knob at the “Change Mode?” prompt will reboot the FS-HDR

in the other operating mode. During reboot, the display shows [Rebooting], goes

dark momentarily, and then shows the percentage of progress as the system

reboots. Reboot should take no longer than 90 seconds. This parameter has no

default setting (is only be used to change to the other mode) and is not saved in

Presets.

HD/SD

4K/UHD

After reboot the FS-HDR will operate in Four Channel (HD/SD) mode.

After reboot the FS-HDR will operate in Single Channel (4K/UHD) mode.

3.1 IP Config

This parameter determines the type of TCP/IP network configuration used by the

FS-HDR. Consult your network administrator about how to set this value.

DHCP

(default)

Static Addr

Select automatic IP address assignment from the LAN DHCP server. If the

FS-HDR cannot find a DHCP server, it fails over to the static IP address.

Assign a static IP address manually (using the following parameter

menus). The FS-HDR factory default static IP address is 192.168.0.2.

3.2 IP Address

This parameter determines the static IP address used by the FS-HDR for TCP/IP

networking. Consult your network administrator about how to set this value.

IP Address variable

IP Config

is set to

DHCP

dynamic addressing (default), the IP Address is set

automatically by the network’s DHCP server.

IP Config

is set to

Static Addr

, manually enter an IP address.

IP Config

is set to

DHCP

and there is a DHCP failure, the IP address is set to

the static IP address. The factory default static IP address is 192.168.0.2.

Octet Value Entry Procedure

Set the octets (numbers between periods) values as follows:
1.  Push ADJUST momentarily to enter edit mode.
2.  Turn SELECT to select the octet you want to edit, indicated by blinking.
3.  Turn ADJUST to enter the new value.

• If you need to revert to the previous setting (undo changes), push SELECT.

4. Push ADJUST momentarily to save and activate the new setting.

• If you want to revert to the default value, hold down ADJUST for 4 seconds.

Summary of Contents for FS-HDR


































































































































Search results

Summary of Contents for FS-HDR

Reviews:

Related manuals for FS-HDR

Brands by name

Popular brands

AJA FS-HDR, Installation And Operation Manual

Search results

Summary of Contents for FS-HDR

Reviews:

Related manuals for FS-HDR

Brands by name

Popular brands