AJA FS-HDR Installation And Operation Manual Download Page 55

Page: 55 / 129

FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 55 www.aja.com

NOTE: The STATUS menu always shows the FS-HDR’s current Ethernet settings. The

parameters shown on the CONFIG Menu Group IP configuration menu may not

display the values the unit is currently using.

Vid 1/2 I/O

(4Ch only) This menu shows the current primary video settings for Video

Processors 1 and 2.

IN1

Input Source

Format

OUT1

Output Source

Format

IN2

Input Source

Format

OUT2

Output Source

Format

Selected (physical) video 1 input & detected format.

Selected video output 1 format & selected audio input

used on output.

Selected (physical) video 2 input & detected format.

Selected video output 2 format & selected audio input

used on output.

Vid 3/4 I/O

(4Ch only) Same as Vid 1/2 I/O status menu, except for Video Processors 3 and 4.

Vid I/O

(SingleCh only) This menu shows the current primary video settings for Video

Processor.

Input Source(s)

Format

GEN

Genlock Source

Status

OUT Format

AudIn

Vid CC

Status

Selected (physical) video 1-4 inputs & detected format.

Selected Genlock source and format.

Selected video output format & selected audio input

used on output

Closed Caption status

Vid 1 Format

(4Ch only) This menu shows the current primary video settings for Video

Processor 1.

IN1

Input Source

Format

BKGD

Backgd Source

GEN

Genlock Source

Format

OUT1

Format

Selected video input source and format.

Selected Background video source.

Selected Genlock source and format.

Selected video output format.

Vid 2-4 Format

(4Ch only) Same as Vid 1 Format menu, except for Video Processors 2-4.

Vid 1 Alarm

(4Ch only) This menu shows the Video Processor 1 alarm status. Absence of alarm

shows as OK. If selections are incompatible, the status of the affected signal

shows Incompat.

IN1

Input Source

Status

BKGD

Backgd Source

Status

GEN

Genlock Source

Status

Rate

Status

Video input source alarm status.

Selected Background video source alarm status.

Selected Genlock source alarm status.

System Output Frame Rate (59/29/23.98, 50/25, 60/30/24)

Vid 2-4 Alarm

(4Ch only) Same as Vid 1 Alarm menu, except for Video Processors 2-4.

Summary of Contents for FS-HDR


































































































































Search results

Summary of Contents for FS-HDR

Reviews:

Related manuals for FS-HDR

Brands by name

Popular brands

AJA FS-HDR, Installation And Operation Manual

Search results

Summary of Contents for FS-HDR

Reviews:

Related manuals for FS-HDR

Brands by name

Popular brands