Agilent Technologies AIC 5000 Installation Manual Download | Manualshive

Page: 25 / 64

background image

AIC 5000 Installation and Configuration

19

Figure 3. AIC 5000 Instrument and SS420x Connections

Note

If you are using a SCSI instrument, it must be
powered ON prior to connecting it to the AIC.

If you are using an instrument with an analog signal, you need to
connect it to an SS420x or other supported A/D converter attached
to the AIC. For details on how to connect an instrument to an A/D,
see the documentation provided with the A/D.

If you are connecting an instrument to the AIC 5000 through the
optional GPIB interface card, you must use the included GPIB port
extender (part number 10834A).

If you are connecting an instrument to the AIC using Ethernet, you
must use the network connector in the PCI slot indicated in Figure
3.

Note

Use only the Agilent-supplied network interface
card in the AIC 5000.

«
...
23
24
25
26
27
...
»

Summary of Contents for AIC 5000

































































Reviews:

No comments

Related manuals for AIC 5000

imageRUNNER ADVANCE C9075S PRO

Brand: Canon Pages: 20

Brand: CAME Pages: 32

Brand: Babybee Prams Pages: 21

SolarCell Remote

Brand: Samsung Pages: 2

Brand: Danfoss Pages: 37

Brand: Daikin Pages: 44

ServeRAID-MR10is

Brand: IBM Pages: 94

ServeRAID-4 Ultra160 Series

Brand: IBM Pages: 20

8271 Nways Ethernet LAN Switch

Brand: IBM Pages: 6

Brand: IBM Pages: 86

Brand: IBM Pages: 205

Brand: IBM Pages: 28

Brand: U-Prox Pages: 3

Brand: U-Prox Pages: 25

Brand: U-Prox Pages: 2

Brand: vacuubrand Pages: 12

Brand: Vacon Pages: 47

Brand: Vacon Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands