Agilent Technologies AIC 5000 Installation Manual Download

Page: 52 / 64

Revision A Installation and Configuration

Setting Time, Date, and Regional Settings

Select

Start

followed by

Control Panel

and select

Date,

Time, Language, and Regional Options

Choose

Customize

and specify the Date & Time and

Time Zone. Close the window.

Check that the time is set correctly, as changing Time
Zone may reset the time.

For regions outside the United States, choose

Change

the format of numbers, dates, and times.

Select the Regional Options appropriate for your
region.

Enable Screen Lock

To prevent unauthorized access to the AIC, enable password
protection with the screen saver.

Select

Start > Control Panel

and choose Appearance

and Themes.

Select Choose a screen saver.

Enter a time of 1 minute, check the box On resume,
password protect, and click OK.

Data System Enterprise Settings

Go to

Start > Run

and type

Regedit

to open the

Registry Editor.

Browse to

MyComputer\HKEY_LOCAL_MACHINE\SOFTWARE
\ChromatographySystem\C:/EZCHROM
ELITE/\CSMain

and enter your Enterprise Machine

name and Enterprise Path in their respective string
fields by double clicking the field name:

Summary of Contents for AIC 5000

































































Search results

Summary of Contents for AIC 5000

Reviews:

Related manuals for AIC 5000

Brands by name

Popular brands

Agilent Technologies AIC 5000, Installation Manual

Search results

Summary of Contents for AIC 5000

Reviews:

Related manuals for AIC 5000

Brands by name

Popular brands