Agilent Technologies AIC 5000 Installation Manual Download | Manualshive

Page: 57 / 64

background image

Revision A Installation and Configuration

51

Update Procedure

The procedure for updating

Elite

version 3.1.6 or later on an

AIC is as follows:

1.

Copy all of the folders (but NOT the files in the
root) from the Instrument Options CD to the USB
memory stick. Copy all of the folders (but NOT
the files in the root) from the Instrument Control
Add-on DVD.

2.

Copy the

Elite

folder, only, from the “AIC Image

Update” folder of the

Elite

Installation CD to the

USB memory stick. The USB drive should look
similar to the following:

Note

AIC Rev. A does not support any RC.Net
Instrument drivers. Trying to configure any
instrument based on RC.Net will cause errors.
To identify RC.Net Refer to the Supported
Modules and Firmware document on the
Manuals folder of the Add-on DVD.

«
...
55
56
57
58
59
...
»

Summary of Contents for AIC 5000

































































Reviews:

No comments

Related manuals for AIC 5000

Brand: S&C Pages: 40

Brand: Manfrotto Pages: 16

Brand: Gardena Pages: 18

VLT Micro Drive FC 51 Series

Brand: Danfoss Pages: 23

Brand: Datavideo Pages: 8

Brand: rada Pages: 16

Grafica DNE-K07

Brand: Paradox Pages: 24

Brand: Panosol Pages: 105

Brand: Pangolin Pages: 8

Compact Comfort VAV12

Brand: SAI HVAC Pages: 16

Brand: Saitek Pages: 15

Brand: saia-burgess Pages: 203

Brand: Sailor Pages: 1

Brand: Yamaha Pages: 5

Brand: Yamaha Pages: 20

Brand: Yamaha Pages: 2

Brand: Eaton Pages: 448

Brand: Eaton Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands