Agilent Technologies AIC 5000 Installation Manual Download | Manualshive

Page: 15 / 64

background image

AIC 5000 Installation and Configuration

9

Figure 2. AIC 5000 Preliminary Setup

4.

Insert the USB memory stick into any USB port of the AIC.

5.

Turn on the AIC by pressing the power button on the front panel.

6.

The installer will run automatically (a low to high tone will be
heard three times). If a low steady tone is heard, the
IconXPInstall.ini file was missing on the USB memory stick.  This
file is located in the XPInstall folder.  If it is not present, turn off
the AIC, remove the memory stick, and recopy the files to the
memory stick using the steps in the “Copy EZChrom Elite Images
to the USB memory stick” section, above.  Then follow the
Preliminary Setup procedure starting with Step 4, above.

7.

Wait for notification that the installation is complete (a high to low
tone will be heard until the AIC is turned off).

8.

Remove the USB memory stick.

9.

A module validation report for the installation can be found in the
Reports folder of the memory stick. Review the module validation
results on a desktop PC, and make sure the validation “Passed.” If
the validation does not pass, carefully perform the installation

«
...
13
14
15
16
17
...
»

Summary of Contents for AIC 5000

































































Reviews:

No comments

Related manuals for AIC 5000

Brand: GARDTEC Pages: 48

Brand: FAAC Pages: 64

Brand: Lawler Pages: 4

Brand: E+E Elektronik Pages: 20

Brand: Eaton Pages: 2

Brand: MacDon Pages: 32

Brand: K&K Pages: 6

Brand: LAE electronic Pages: 7

Brand: LAE electronic Pages: 2

Brand: Lamtec Pages: 136

TEMP2000 Series

Brand: Samwontech Pages: 91

Brand: Warren rupp Pages: 18

Brand: Yamaha Pages: 100

Brand: WAM Pages: 62

Brand: walimex Pages: 7

Brand: Walchem Pages: 2

Brand: Walchem Pages: 73

Brand: Walchem Pages: 126

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands