Agilent Technologies AIC 5000 Installation Manual Download | Manualshive

Page: 40 / 64

background image

34

AIC Revision B Installation and Configuration

Install the SS420x

If your instrument provides an analog detector signal, you may use
the SS420x analog to digital converter box. If you are using a digital
instrument, you do not need an SS420x.

Connect the SS420x interface to the AIC using the serial
communications cable provided. Connect one end of the cable to
the serial port on the back of the SS420x. Connect the other end of
the cable to any serial port on the AIC. Make sure to tighten each
connector.

Connect the power cord into the receptacle on the rear of the
SS420x and then plug the SS420x power supply into a standard
electrical outlet.

The red power LED should light. The four (4) green channel
indicator LEDs will sequentially light up during the power-up test.
When the test is complete, the green LEDs will go off and the
interface is ready to use. If this sequence does not successfully
complete, the SS420x must be powered off and then on again.

For more information, see the

Agilent SS420x Interface User’s

Guide

.

Configure the SS420x

If you will be using an SS420x attached to the AIC (required for
analog acquisition), it will need to be configured locally. If you are
not using a local SS420x, you may skip this section.

1.

Start the data system software by going to

Start > All Programs

> Chromatography > EZChrom Elite

. Go to Tools, Interface

Configuration and select the SS420x.

2.

From the SS420x configuration dialog, select the Serial port to
which the SS420x is connected and then check the

Installed

box

to enable the configuration of the interface. Then proceed to
select the appropriate settings for the interface.

Baud Rate

The communication baud rate is displayed here. To change
the baud rate, click

Advanced

.

«
...
38
39
40
41
42
...
»

Summary of Contents for AIC 5000

































































Reviews:

No comments

Related manuals for AIC 5000

Brand: Bartlett Pages: 30

Brand: K&K Pages: 6

Brand: Datalogic Pages: 15

Brand: Universal Remote Pages: 20

Brand: Decagon Pages: 27

Brand: Frico Pages: 12

Brand: Cypress Pages: 3

IB-TRON 4000 SOL

Brand: INSBUD Pages: 14

Brand: babyplus Pages: 28

Brand: Therma-Stor Pages: 20

Brand: Intermatic Pages: 3

Brand: Bardiani Valvole Pages: 118

Brand: Phoenix Contact Pages: 40

Brand: Digiplex Pages: 48

Brand: Moog Pages: 15

Brand: Danfoss Pages: 14

Brand: zeeltronic Pages: 15

Brand: M-system Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands