Agilent Technologies AIC 5000 Installation Manual Download

Page: 53 / 64

Revision A Installation and Configuration

Close Regedit.

Restart the AIC.

Start the data system from

Start > All Programs >

Chromatography > EZChrom Elite

. When you are

prompted that you‟ve been assigned rights and you
must restart, restart the AIC.

Configure the SS420x

If you will be using an SS420x attached to the AIC (required
for analog acquisition), it will need to be configured locally. If
you are not using a local SS420x, you may skip this section.

Start the data system software by going to

Start > All

Programs > Chromatography > EZChrom Elite

. Go to

Tools,

Interface Configuration

and select the

SS420x

From the SS420x configuration dialog, select the Serial port to
which the SS420x is connected and then check the

Installed

Summary of Contents for AIC 5000

































































Search results

Summary of Contents for AIC 5000

Reviews:

Related manuals for AIC 5000

Brands by name

Popular brands

Agilent Technologies AIC 5000, Installation Manual

Search results

Summary of Contents for AIC 5000

Reviews:

Related manuals for AIC 5000

Brands by name

Popular brands