Agilent Technologies AIC 5000 Installation Manual Download | Manualshive

Page: 9 / 64

background image

AIC 5000 Installation and Configuration

3

2

About the AIC

The AIC is a device that controls instruments and acquires data
digitally. It is for use in client/server environments only. Each AIC
can control and acquire digital data from up to 4 GC or LC
instruments, or up to 16 analog channels of data (A/D required), up
to 2 photodiode array detectors (PDA) or combinations of the
above.

Please see the Agilent Technologies Website www.Agilent.com and
browse for Technical Support for Life

Sciences and Chemical

Analysis for information on EZChrom Elite software version
support for AICs.

Note

There are three versions of the AIC: The
AIC 5000 is black in color and has
“Instrument Controller 5000” stenciled on
the front of the unit. Revision B is silver
in color and is marked with a “Revision
B” sticker on the rear. Revision A has
limited instrument support for versions
after

EZChrom Elite Revision 3.2.1. It is

black in color and is marked with a
“Revision A” sticker on the rear or has no
sticker. AIC Rev A is not covered in this
document.

Note

The AIC is shipped with a USB memory
stick, which is required for software
installation and updates. Please keep this
in a safe place for future use.

«
...
7
8
9
10
11
...
»

Summary of Contents for AIC 5000

































































Reviews:

No comments

Related manuals for AIC 5000

Brand: Hansen Pages: 4

Brand: Rain Bird Pages: 48

Brand: XBOX Pages: 4

Brand: Canarm Pages: 3

Brand: Yardney Pages: 8

Brand: eclisse Pages: 40

Brand: Samson Pages: 52

Brand: Gardena Pages: 14

Brand: Gardena Pages: 8

Brand: V2 ELETTRONICA Pages: 72

Brand: jbc Pages: 44

Brand: jbc Pages: 8

Brand: Samson Pages: 78

TEMP2000 Series

Brand: Samwontech Pages: 91

Brand: Warren rupp Pages: 18

Brand: Yamaha Pages: 100

Brand: ZKTeco Pages: 20

Brand: ZKTeco Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands