manualshive.com logo in svg

Aerotech Automation1 XR3 Series, Hardware Manual

Share
Download
Aerotech Automation1 XR3 Series Hardware Manual Download Page 84

2.11. HyperWire Interface

The HyperWire bus is the high-speed communications connection from the controller. It operates at 2
gigabits per second. The controller sends all command and configuration information through the
HyperWire bus.

HyperWire cables can be safely connected to or disconnected from a HyperWire port while the PC and/or
drive is powered on. However, any changes to the HyperWire network topology will disrupt
communication and you must reset the controller to re-establish communication.

WARNING

: Do not connect or disconnect HyperWire cables while you are loading

firmware or damage to the drives may occur.

Table 2-56:

HyperWire Card Part Number

Part Number

Description

HYPERWIRE-PCIE

HyperWire adapter, PCIe x4 interface

Table 2-57:

HyperWire Cable Part Numbers

Part Number

Description

HYPERWIRE-AO10-5

HyperWire cable, active optical, 0.5 m

HYPERWIRE-AO10-10

HyperWire cable, active optical, 1.0 m

HYPERWIRE-AO10-30

HyperWire cable, active optical, 3.0 m

HYPERWIRE-AO10-50

HyperWire cable, active optical, 5.0 m

HYPERWIRE-AO10-200

HyperWire cable, active optical, 20.0 m

2.11. HyperWire Interface

XR3 Hardware Manual

84

www.aerotech.com

Summary of Contents for Automation1 XR3 Series









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands