manualshive.com logo in svg

Aerotech Automation1 XR3 Series, Hardware Manual

Share
Download
Aerotech Automation1 XR3 Series Hardware Manual Download Page 21

1.1. Electrical Specifications

The electrical specifications for the XR3 drive chassis are listed in

Table 1-3

and the electrical

specifications for the servo amplifiers in

Table 1-4

.

IMPORTANT

: These electrical specifications represent the maximum capability of a

feature. System constraints can result in lower performance. For example, the motor
output specifications are affected by the Bus supply, the number of axes that are
operating at the same time, the type of motion, the AC Line voltage, and motor
requirements.

Table 1-3:

Chassis Electrical Specifications

Description

Option

Specification

Bus Voltage Options
[Factory Configured]

-VB1

±10 VDC (200 W Power Supply), bipolar

-VB2

±20 VDC (200 W Power Supply), bipolar

-VB3

±30 VDC (200 W Power Supply), bipolar

-VB4

±40 VDC (300 W Power Supply), bipolar

-VB5

±80 VDC (300 W Power Supply), bipolar

-VB7

+160 VDC, unipolar

-VB8

+320 VDC, unipolar

Input Current

-VL1

115 VAC, 10 A Maximum

-VL2

230 VAC, 5 A Maximum

-VL3

100 VAC, 10 A Maximum

-VL4

200 VAC, 5 A Maximum

AC Power Input

AC input (Switch Selectable): AC Hi, AC Lo, Earth Ground ( ),

l

100 VAC (90-112 VAC, 50/60 Hz)

l

115 VAC (103-127 VAC, 50/60 Hz)

l

200 VAC (180-224 VAC, 50/60 Hz)

l

230 VAC (207-254 VAC, 50/60 Hz)

Note: If the XR3 contains an offline Bus power supply, the AC Input will be
limited to one AC input range.

Inrush Current

32 A Peak

Auxiliary Power Outputs

+5 V provided on all axis feedback connectors for encoder, Hall,
and limit power.
+5 V provided on I/O connectors

Protection

The AC power cord serves as the mains breaker and provides 10
A, Supplemental Protection only.
Internal Bus supply fusing.
Amplifier Output short circuit protection.
Peak and RMS over current limit.
Over Temperature shutdown.
Bus supply inrush current limit during initial power-on.

Indicator (Power)

Opto and transformer isolation between control and power
stages.

Indicator (Enabled)

Power switch contains a power-on indicator.

Protection

Individual Amplifier LED’s indicates drive enabled state.

XR3 Hardware Manual

1.1. Electrical Specifications

www.aerotech.com

21

Summary of Contents for Automation1 XR3 Series









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands