manualshive.com logo in svg

Aerotech Automation1 XL5e, Hardware Manual

Share
Download
Aerotech Automation1 XL5e Hardware Manual Download Page 25

Chapter 2: Installation and Configuration

Unpacking the Chassis

IMPORTANT

: All electronic equipment and instrumentation is wrapped in antistatic

material and packaged with desiccant. Ensure that the antistatic material is not damaged
during unpacking.

Inspect the container of the XL5e for any evidence of shipping damage. If any damage exists, notify the
shipping carrier immediately.

Remove the packing list from the XL5e container. Make sure that all the items specified on the packing
list are contained within the package.

The documentation for the XL5e is on the included installation device. The documents include manuals,
interconnection drawings, and other documentation pertaining to the system. Save this information for
future reference. Additional information about the system is provided on the Serial and Power labels
that are placed on the XL5e chassis.

The system serial number label contains important information such as the:

l

Customer order number (please provide this number when requesting product support)

l

Drawing number

l

System part number

XL5e Hardware Manual

Chapter 2: Installation and Configuration

www.aerotech.com

25

Summary of Contents for Automation1 XL5e















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands