ADTRAN 1202155L1 Page 88 User Manual Download

Page: 88 / 146

Chapter 5. Configuration Menu

5-26

TDU 120e User Manual

61202156L2-1

NET/DATA FAIL

Backup occurs on the same conditions as

NET FAIL

plus loss of data transitions on the data the Nx56/64
receives from the network.

Pattern Verify

Selects whether or not the DBU will use its pattern
generator and receiver to authenticate backup
attempts. When the local and remote units are both
Nx/DBUs, set to

NABLE

; otherwise set to

ISABLE

Choices:

NABLE

ISABLE

Backup Delay

Selects the time allowed to elapse between the net-
work going into alarm or no data transmissions and
the backup beginning.
Choices:

SEC

, 3

SEC

, 10

SEC

, 30

SEC

, 1

MIN

, 5

MIN

Restore Delay

Selects the time that elapses between the network
going out of alarm or data being received and the
backup call being taken down. If

EVER

is selected,

the user must deactivate the backup mode.
Choices:

SEC

, 3

SEC

, 10

SEC

, 30

SEC

, 1

MIN

, 5

MIN

NEVER

Retry Delay

Selects the time between redialing the external DCE
after failed dial attempts.
Choices:

SEC

, 30

SEC

, 1

MIN

, 5

MIN

, 10

MIN

Num Retries

Selects the number of times the DBU will attempt to
redial if unable to connect.
Choices:

ONE

NLIMITED

TIMES

Summary of Contents for 1202155L1



















































































































































Search results

Summary of Contents for 1202155L1

Reviews:

Related manuals for 1202155L1

Brands by name

Popular brands

ADTRAN 1202155L1, User Manual

Search results

Summary of Contents for 1202155L1

Reviews:

Related manuals for 1202155L1

Brands by name

Popular brands